Weed Eater

If you are using a single liner weed eater, then you are fully aware that the plastic string will eventually come off at some point in time. You also know that the reason for this is the constant contact with grass, weeds and hard objects. When the head of the weed eater hits the ground a few times, that’s the starting point for the spool to lose its ability to hold the string in place. And overtime, it may become useless and you’ll be forced to replace it.

When this happens, you have no other choice but to add a new string to the spool of your weed eater and replace the damaged spool immediately.

So if you are searching for a detailed guide that explains clearly about how to change a string in the single liner weed eater, you are in the right place!

We’ll be discussing about the step by step instructions on changing a string in the single liner weed eater, general FAQs about the weed eater string and much more.

So let’s get started without any further delay!

How to Change a String in a Single Liner Weed Eater?

The string of the single liner weed eater is very essential because, you’ll be able to cut weeds, grass and unwanted greens from your yard with it. So, having a quality string in your weed eater is a must. The housing that holds the string in place and the spinning wheel is called the spool.

Taking care of it is also important. Why? Because when you maintain the spool well, you can actually extend the lifespan of the string to a considerable amount of time.

Purchasing a single liner weed eater with quality string is critical. Cheep plastic strings will melt away after few uses. For your information, the string of the weed eater comes in single and double line formats.

You’ll notice that after some uses, your single liner weed eater invariably stops working because there is no string left. So if you know how to change a single liner weed eater string at that moment, it’ll save you a lot of time and unnecessary headache.

So in the upcoming section, we are going to give you a step by step instruction on how to change the string in the single liner weed eater.

Ready? Here we go!

Related: How to Clean a Weed Eater Carburetor? A Step by Step Guide

Step by Step Instructions on How to Change a String in the Single Liner Weed Eater

Choosing the Right String

It is very important that you choose the right string for your single liner weed eater. When you unknowingly purchase a longer or a thicker string, it won’t go through the hole and it’ll be a complete waste of your time and money. To avoid this situation, always refer the product manual and note down the exact string size for the model you own.

If you don’t have it with you, no worries! Go to the manufacturer website and you’ll find the exact string size you need for your model. Calling the customer care of the manufacturer is also a good idea.

After selecting the right string size, try to cut the string to the appropriate size for that model. It can be from 10 to 25 inches long. If you aren’t sure the length you need, always cut a little extra. This is simply because it is very easy to trim the string to the exact size rather than fitting it fully into the weed eater, realizing that it is small and removing it from the spool.

Remove the Retaining cap

Before removing the retainer cap, make sure that the weed eater is cooler. It’ll prevent your hands from getting heat burns. To remove the retaining cap, you’ll need to either press two or three side tabs or unscrewing it from the head of the weed eater.

The removing mechanism for the retaining cap completely depends on the kind of weed eater model you have, but you can figure it out easily. After all, you are just going to open a cap.

Related: 10 Best Weed Eater review

Locate the Starter Hole in the Removed Spool

The starter hole will be in the middle of the spool. After you find it, insert the tip of the string into the hole. When you complete that, check throughout the spool for the imprint of arrows.

Start to rap the string in the direction of the arrow. But sometimes, you’ll see that the arrows are given by the manufacturer at the bottom of the cap. And those arrows may worn  down after a certain amount of usage.

If this is the case, just try to rap the string in an anti-clockwise method. If you rap it in a clockwise method, there is a high-possibility that the string may come off right after you start the weed eater engine.

You definitely don’t want that to happen. Right? and in the end, it’ll be an extra work for you to fix the string again. Try rapping the string in a neat line and after you notice that there are only 5 to 6 lines remaining, snap it into the retainer cap so that it holds the string in place.

Related: 11 Best Hedge Trimmer (Corded & Cordless Trimmers Review)

Attach the Spool to the head of the Weed Eater

Hold the spool in a way that the retainer side of the spool lines up to the perfect slot of your cap head. Now, remove the string from the retainer and feed it through the slot. After you complete the process, reattach the retainer cap to the weed eater.

Now you are ready to have a productive day of weed removing from your yard!

Conclusion

We hope that our guide on how to change a string in the single liner weed eater would have provided you answers for all your questions. Apart from a single liner weed eater, there are double liner and speed feed weed eaters available in the market. So carefully consider your needs before you go for purchasing a particular model.

Want to include your thoughts about this guide? Put them in the comments section below!

FAQs about Weed Eater Strings

What are the Things to Consider when Purchasing a String for your Weed Eater?

Here’s a list of things you need to consider when purchasing a string for your weed eater.

  • Understanding the string size.
  • Getting a proper knowledge about the various string shapes.

Below, we’ll give you the various string shapes you’ll find in the market.

  • Round trimmer string.
  • Serrated trimmer string.
  • Multi-sided trimmer string.
  • Twisted trimmer string.

How to Make Your Weed Eater String Last Longer?

Here’s a list of things you can do to increase the lifespan of your weed eater string.

  • Make sure to use the weed eater string properly.
  • Don’t overuse it.
  • Figure out the right thickness of string you need for your weed eater.
  • Get a longer string for the spool.
Previous articleBasic Car Care For First Time Owners
Next articleHow to Lock a Bike Properly? A Detailed Guide
With over 12 years of experience, she is a proficient content writer and editor specializing in a diverse range of subjects, including technology news, country news, arts, science, travel, and automobiles.

LEAVE A REPLY

Please enter your comment!
Please enter your name here